RATTAN FILL STICKS FOR BAMBOO SHAFTS
Rattan filling sticks for making the hollow Bamboo shafts solid at the ends.Apply these with sufficient superglue or 2k epoxy and you can finish the shafts like you are used to, the same way as solid wooden shafts.Supplied per 24 pieces, 6 cm long (approx. 2 inch)
ARROW PULLER GRIP 'GRASPER' BLACK
Rubber grip with belt hook loop. The Grasper by AvalonThis grip helps you with gripping arrow shafts while applying screw-on arrowheads and pulling arrows out of tough targets.✓Soft molded handgrips✓Belt hook loop✓Deep wedge for strong support
TEMPLATE SET, WARBOW SOCIETY SHAPES, 5 TEMPLATES IN WOODEN BOX
Template set, English and Dutch Warbow Society shapes, 5 templates These templates are used after the full feathers have been glued to the shaft. Some painters tape and a scalple will help you on the project. contains : Wooden box (flatpack) Standard arrow shape Livery arrow shape shape Crecy ...
LEG SINEW STRIPS APPROX. 6-9 INCHES
Dried unprocessed leg sinew.For backing self bows and tying fletching or points to arrows. Sold per piece. Average length 6-9 inches. Not processed, just dried
BOHNING FLETCHING TAPE
€10,95
BOHNING FLETCHING TAPE
Well known sticky tape to fix your fletchings with. Will do, depending on the length of the fletchings, 3-4 dozen arrows. ✓Designed for Mylar vanes & feathers ✓Works on all shaft surfaces ✓Length - 720" ✓Width - 0.1875" ✓Machine cut without lubricant so no dead zones in the roll ✓One roll fl...
BOHNING CREST-LAC 1OZ JAR/30 ML, CRESTING PAINT
Bohning's water-based Crest-Lac paints produce a glossy, durable finish. We formulated them specifically for cresting and dipping arrows, with optimal flow and leveling so brush marks don't show when dry, and non-bleeding properties that achieve crisp edges on even the finest cresting stripes. Bo...
EMT (Easy Measurement Tool) in clear Perspex or MDF based wood
Fairbow EMT (easy measurement tool) in Clear Perspex or MDF based wood. All the sizes for arrows we use, along with feather length indicated in inches, feather hight and length for EWBS and DWS arrows.A must have for every fletcher.
TEMPLATE SET, SHIELD SHAPES, 7 TEMPLATES
Full set of shield templates. Contains :nrs 9, 10, 11, 12, 13, 39 and 64. nr. 9, 3 inch nr 10, 4 inch nr 11, 5 inch nr 12, 4 inch superfast nr 13, 5 inch superfast nr 39, 1 inch nr 64, 6 inch please select left or right wing in the menu
UHU PLUS ENDFEST 300 2 TUBES 33 GRAM
Set of two 15 ml tubes of 2 K epoxy glue. super strong 2 K epoxy, Please mix 1:1 ratio 90 muinutes open time.solid after 6 hrs at room temperature.Fully hardened at roomtemperature after 24 hours
ALUMINUM TAPERTOOL FOR WOODIES 5/16 OR 11/32 BY BUCKTRAIL
Aluminum Taper toolLike and old fashioned pencil sharpener but better and in the correct tapering/angle for your wooden arrows.✓Works for 5/16 or 11/32 ✓Replaceable knives✓Tapering for nocks and arrowheads✓With aluminum collectors
TOPHAT ASSEMBLY TOOL
Die-cast zinc and steel assembly tool for Tophat products and especially to help you with any screw on arrow head
Feather Cutting Template EWBS DWS cut-on-shaft
Feather cutting template EWBS DWS. Easy to use, clear Perspex feather cutting template . First glue on the full height-, uncut feather, then using the template, cut inside the template...
BOHNING FLETCH FUSE SUPERGLUE/INSTANT GLUE
Fletch Fuse is Bohning's budget-friendly instant glue designed for vanes, points, inserts, outserts, & swedged nocks. It works on all shaft types - carbon, aluminum, fiberglass, wood, and wrapped or crested arrows. Fletch Fuse adhesive is slightly thicker and contains more additives than Blaz...
TEMPLATE SET, PARABOLIC SHAPES, 9 TEMPLATES
Full set of Parabolic templates. contains :nrs 14,15 16,17,18,19, 20, 21 and 39. nr. 14, 3 inch nr 15, 4 inch (will be sent later) nr 16, 5 inch nr 17, 6 inch nr 18, 3 inch superfast nr 19, 4 inch superfast nr 20, 5 inch superfast nr 21, 6 inch superfast nr 38, 1 inch please select left ...
GLUE MIXING CUP
Mixing cup for glue with proper indications for quantity and mixture.fit for 350 ml.One use only but extremely easy!Ready to ship!
TOPHAT SHAFTFORMER SET 5/16 and 11/32
This tool helps you to make the shaft exactly the required size by squeezing it in a conical tube or collar inside the tool. Use a battery-drill for best results. The set comes with 5/16, and 11/32 collars